-
1 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
2 предельная величина
предельная величина
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
limit value
A workplace exposure criterion or standard that determines if a facility or building has a concentration of a substance to which most workers can be exposed without harmful or adverse effects. (Source: HEG)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > предельная величина
См. также в других словарях:
without limit — index indeterminate, infinite, profuse Burton s Legal Thesaurus. William C. Burton. 2006 … Law dictionary
without limit — with no restriction * * * without limit : without being controlled or stopped : without being limited allowing costs to increase without limit • • • Main Entry: ↑limit … Useful english dictionary
without limit — with no boundary, with no restrictions … English contemporary dictionary
without stint — Without limit; without any specified number … Black's law dictionary
without stint — Without limit or restriction on number or amount … Ballentine's law dictionary
Limit of a function — x 1 0.841471 0.1 0.998334 0.01 0.999983 Although the function (sin x)/x is not defined at zero, as x becomes closer and closer to zero, (sin x)/x becomes arbitrarily close to 1. It is said that the limit of (sin x)/x as x approache … Wikipedia
limit — {{Roman}}I.{{/Roman}} noun ADJECTIVE ▪ outer ▪ northern, southern, etc. ▪ three mile, etc. ▪ city … Collocations dictionary
limit — n. & v. n. 1 a point, line, or level beyond which something does not or may not extend or pass. 2 (often in pl.) the boundary of an area. 3 the greatest or smallest amount permissible or possible (upper limit; lower limit). 4 Math. a quantity… … Useful english dictionary
limit — Palena, kaupale, oki. ♦ To limit, kaupalena. ♦ Land limit, palena āina, kapaha i. ♦ Off limits, kapu, ho okapu ia, pāpā ia. ♦ Without limit, ana ole, palena ole, a ole o ka e mai, a ole o kana mai, a ohe launa. ♦ Limited,… … English-Hawaiian dictionary
limit# — limit n Limit, bound, confine, end, term are comparable when they mean an actual or imaginary line beyond which a thing does not or cannot extend. Limit is the most inclusive of these terms because it carries no necessary implication of number,… … New Dictionary of Synonyms
Limit loads — Limit load is the maximum load that a structure can safely carry. It s the load at which the structure is in a state of incipient plastic collapse. As the load on the structure increases, the displacements increases linearly in the elastic range… … Wikipedia
